Located inside your home is a circuit breaker box or panel that contains circuit breakers. Some homes have more than one panel. There may be a main panel plus one or more sub-panels in other locations.

There will usually be a large main breaker at the top of the panel with a high rating. The breakers for your branch circuits are physically smaller and have a lower amp rating. Be advised that shutting off the main breaker will also shutdown the branch circuits, but there is still high voltage in the breaker panel. The main wire leads into the panel are still active, and shutting off the main breaker will not stop current flow to these main leads.

If you decide to go ahead with new cabinets, plan your job. Take measurements, make note of appliances and fixtures that have to be moved. Are you changing the color of the entire room? What about new light fixtures? How about the floor? This might be a good time to install new ceramic floor tile.

Get brochures from several cabinet companies and compare features, warranties, and prices. These will tell you what standard sizes are available, finishes, styles, materials, and hardware options. You may have to order a custom size to fit your area, but it is usually much less expensive to use standard sizes.

Draw a layout of your cabinet plans to give you an idea of how everything will line up and fit together. Make sure to include appliance and fixture locations. Check for interference with existing fixtures and lighting. If you are not going to install new light fixtures, make sure the new cabinets do not create shadows on the counter tops.

Look for interference with cabinet doors when they are opened. If you have a built-in range, will it fit the new opening? What about the exhaust fan - will you have to relocate the exhaust pipe and electrical connections?

Check the cabinet heights. If you are especially tall or short, see how far up you can comfortably reach. Many upper cabinets are designed to have an empty space between the tops and a standard height ceiling, while others will extend all the way to the ceiling.

If one of your cabinets will go over your sink or stove, make sure to allow space underneath it for working, and to attach lighting or a stove hood.

Be sure that upper cabinets line up with lower cabinets, and allow for windows and other features in the wall. Consider how you use your kitchen.

Items Needed for a Professional Job:

• Several carpenter's levels or laser levels of different lengths

• Lots of wood shims for leveling

• Clamps to hold cabinets together while you are arranging.

• Stud finder

• Counter top

• Two 2x4s or a cabinet jack

• Hinges

• Drawer pulls and door handles

• Any sinks, faucets, or other fixtures you will replace at the same time

• Paint and replacement flooring

• Caulk

• Basic power tools such as circular saw, drill, jigsaw, and screw gun

• Screws for hanging cabinets

Empty the old cabinets completely, then remove the doors and shelves before unscrewing the cabinets from the walls. Most shelves simply lift off of pegs, but some need to be unscrewed or pried off their supports.

Make certain that you support the upper cabinets as you remove the mounting screws. If the upper cabinets are a one-piece unit, you may have to separate them to avoid damaging adjacent walls.

After the old cabinets are removed, do any painting and floor work before installation begins. This would be a good time to do plumbing work if needed, assuming the pipes are exposed. See my post on how to sweat solder copper pipe if you need help with this.

Assemble the cabinets, but do not put the doors on yet. Take the time to make sure that the cabinets are assembled as securely, squarely and evenly as you can. Install upper cabinets first if possible, so that you will not need to work over the lower units.

Locate studs with a stud finder and use a level to draw a line down at their locations. Measure from the ceiling to mark the height of the cabinet brace or rail you will fasten to the studs.

Upper cabinets go first, starting at one end or in a corner. Be sure to arrange for a helper to lift and support them during installation. Follow all manufacturer instructions for installation.

Now mark the locations of your studs for the lower cabinets. Move them into place and check which cabinet sits highest. It's easier to shim the others up to this height than to shorten the tall one.

Make cutouts for plumbing, electrical, etc. Be sure these are accurate, and leave a little extra room so cabinets can be moved a little and not interfere with pipes or wiring.

Level the top of the cabinets by shimming under and behind them. Remember that you will install a counter top on the cabinets, so you want this reasonably level and all the joints flush. Also look at the appearance of the cabinet fronts and make sure those are even.

Sub-floor Preparation

The surface to be tiled must be smooth, dry, and clean. All contaminants must be removed by sanding, scraping or chipping. Any imperfections in the floor should be patched with a waterproof patching compound.

Snap chalk lines with a 90 degree intersection, preferably in the center of the room. Be patient. The more time you invest in laying out your area the better your project will go. Solve your layout questions before the adhesive is even mixed.

For best results, all tiling materials and adhesives should be at 50 to 70 degrees for 24 hours before and 48 hours after installation. Thoroughly mix the mortar with clean water to a toothpaste like consistency. It is best to only mix what can be used in 30 minutes. Stir mixture occasionally to maintain consistency. In the event the mix becomes stiff in the pail, discard and make a fresh batch.

Lumber intended for general construction is subdivided into stress graded, non-stress graded, and appearance categories. Stress graded and non-stress graded lumber are required to have consistent structural integrity. With appearance lumber, visual quality of the piece is most important and structural integrity is a secondary requirement.

The term "yard lumber" is often applied to the non-stress graded and appearance lumber that is sold by retail lumberyards. With such lumber, grading is done on the better side of a piece after drying and surfacing, and grades are designated by specifying the allowable size and number of defects (e.g., knotholes). This contrasts with hardwoods where most grades are determined from the poorer side of each piece on the basis of a specified number of clear cuttings. Another distinction is that hardwoods are typically graded prior to drying and surfacing.

Non-Stress Graded Lumber

With non-stress graded lumber, pieces are graded primarily for serviceability but appearance is also considered, especially in the higher grades. Imperfections such as knots and knotholes are allowed to become larger and more frequent as the grade drops. The primary product is boards that are less than 2 inches in nominal thickness and 2 inches or more in nominal width. Common nominal widths are 2, 3, 4, 6, 8, 10, and 12 inches. Lengths are usually from 6 to 18 feet in increments of 2 feet. Three to five different Common grades may be applied to boards in this group depending upon the species and the lumber manufacturing association involved. In descending order of quality, the grades are:

Most concrete projects are measured by the foot for length and width, and inches for thickness. So how do you determine the cubic yards of concrete to order?

Let’s say you are pouring a slab that measures 20 feet wide, 20 feet long, and 4 inches thick. Start by calculating the square feet of surface area. The formula is:

Before starting, review the features of the area. What color are the walls, countertop, floor and appliances? Are the cabinets light or dark? What type of lighting is present, and what does it illuminate? What color and type are the fixtures? If your cabinets are dark, you may want to lighten-up the area. If you have under-cabinet lighting, the backsplash could probably be done in a medium color tone so it doesn’t contrast with the cabinetry.

Surface Preparation

Tile can be installed over most substrates if they are clean, smooth and dry. Check with your supplier to see if the tile you have chosen requires a specific underlayment. Repair and level any damaged or uneven areas. Make certain your countertop is level. If not, insert shims between the lower cabinets and the countertop. Turn off power and water to any outlets within or near your work space. Be careful! Electric wires and plumbing run between studs in walls. Don’t make the mistake of cutting into either while they are still live.